Versions Compared

Version Old Version 14 New Version 15
Changes made by

Wolfgang Scheucher

Wolfgang Scheucher

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

PANS-AIMDescription (PANS-AIM)AIXM 5Definition (AIXM 5.1.1)Remarks
DesignatorThe full textual designator of TLOFTouchDownLiftOff.designator

TouchDownLiftOff: A load bearing area on which a helicopter may touch down or lift-off.

designator: The designator of the touch down and lift-off area.


Centre point - PositionGeographical location of TLOF geometric centre

TouchDownLiftOff.aimingPoint.ElevatedPoint

and

TouchDownLiftOff.aimingPoint.ElevatedPoint.horizontalAccuracy

aimingPoint: Aiming point for the TouchDownLiftOff zone.

horizontalAccuracy: The difference between the recorded horizontal coordinates of a point and its true position referenced to the same geodetic datum expressed as a circular error at 95 percent probability.

Warning
titleAIXM 5.1(.1) Issue_021_TLOF_aimingPoint

In AIXM only the aiming point of a TLOF can be coded. The aiming point is not the same position as the centre point of a TLOF.

According to ICAO Annex 14, Volume II,

An aiming point marking should be provided at a heliport where it is necessary for a pilot to make an approach to a particular point before proceeding to the TLOF.

The aiming point marking shall be located within the FATO.

Currently in AIXM it is not possible to define two different points for a TLOF.

Workaround for AIXM 5.1(.1):

  • In case only the centre point location shall be encoded use aimingPoint.
  • In case both locations shall be encoded use aimingPint for the aiming point and code the centre point location as Note.

Status AIXM 5.1: See CCB AIXM-268

Centre point - ElevationElevation of the TLOF geometric centre

TouchDownLiftOff.aimingPoint.ElevatedPoint.elevation

and

TouchDownLiftOff.aimingPoint.ElevatedPoint.verticalAccuracy

elevation: The vertical distance of the point measured from Mean Sea Level (MSL).

verticalAccuracy: The difference between the recorded elevation of a point and its true elevation referenced to the same vertical datum expressed as a linear error at 95 percent probability.


Centre point - Geoid undulationWGS-84 Geoid undulation at TLOF geometric centre position

TouchDownLiftOff.aimingPoint.ElevatedPoint.geoidUndulation

and

TouchDownLiftOff.aimingPoint.ElevatedPoint.horizontalAccuracy

geoidUndulation: The distance of the geoid above (positive) or below (negative) the mathematical reference ellipsoid at the location of the point.
Info
titleInfo for accuracy

In AIXM 5 the verticalAccuracy refers to both the elevation and the geoidUndulation.

Hence, if the verticalAccuracy is coded for the elevation but the accuracy for the Geoid undulation is not known, this should be put into a corresponding Note.

LengthThe longitudinal extent of TLOF

TouchDownLiftOff.length,

and

TouchDownLiftOff.annotation.Note.propertyNamevalue equal-to 'length'


length: The value of the physical length of the touchdown and lift-off area.
Warning
titleAIXM 5.1(.1) issue_022_TLOF_length

PANS-AIM defines an accuracy for the TLOF length. AIXM 5.1.1 does not have a dedicated attribute for that purpose.

Workaround for AXM 5.1(.1): A Note may be used.

Status: see CCB AIXM-269

WidthThe transversal extent of TLOF

TouchDownLiftOff.width,

and

TouchDownLiftOff.annotation.Note.propertyNamevalue equal-to 'width'


width: The value of the physical width of the touchdown and lift-off area.
Warning
titleAIXM 5.1(.1) issue_023_TLOF_width

PANS-AIM defines an accuracy for the TLOF width. AIXM 5.1.1 does not have a dedicated attribute for that purpose.

Workaround for AXM 5.1(.1): A Note may be used.

Status: see CCB AIXM-269

Surface typeThe surface type of TLOFTouchDownLiftOff.surfaceProperties.SurfaceCharacteristics.composition

surfaceProperties: Surface characteristics of the runway.

composition: The type of the predominant material of which a surface of the movement area is composed.