Page Comparison

Supported schedules

There are three types of schedules supported for Digital NOTAM Events:

• daily schedules;
  e.g. "daily from 09:00 to 17:00";
• date based schedules, including "on date" and "date range" options;
  e.g. "1/10 09:00-15:00 and on 3/10 10:00-12:00";
• days of the week based schedules, including "on weekday", or "from weekday...to weekday" options;
  e.g. "every Monday from 13:00 to sunset".

Not supported schedules

Combining different schedule types in a single NOTAM is forbidden. It is considered that such combined schedules could become too complex for being understood and would have a high potential for providing conflicting information. For example, "daily 0900-1700 and each MON 1900-2300" would not have a clear meaning. Is the schedule for Mondays just 1900-2300, or is it both 0900-1700 and 1900-2300? Therefore, such combined schedules are not supported.

Note that the concept of "weekday ranges" (such as "MON-WED") is also not supported in this specification. However, the automatic NOTAM generation rules for item D ensure that a set of consecutive weekdays with a similar start/end time will generate a "weekday range", according to the OPADD recommendations. This does not exclude implementing an HMI that allows the input of weekday ranges, for efficiency reasons. They will have to be converted into individual weekday records in AIXM.

Also not supported are schedules that use both startTime and StartEvent or both endTime and endEvent, such as "SR or 07:00, whichever is earliest". Such schedules are sometimes encountered for static data, as they need to cover longer time periods. It is not justified to use such combinations in a NOTAM schedule.

In addition, according to the OPADD, item D is not allowed to exceed 200 characters. The application interface should check the length of the item D that results from the schedule encoding and invite the operator to split the NOTAM into two separate events in case this limit is exceeded. The HMI should allow copying a draft event into a second draft event.

UML class diagrams representation

The limitations identified above correspond to a subset of the general AIXM model for schedules. The following UML diagram shows only the classes and properties which may be used for Digital NOTAM coding. For reference, the full AIXM schedules model is described here: AIXM - Schedules).

The data type or the sub-sets of allowable values that may be used in a Digital NOTAM encoding are shown in the following diagram: 

TEMPDELTA - additional versus complete hours

As explained in the general coding rules for schedules - Relation with TimeSlice validity, a TEMPDELTA shall contain a complete description of the operating times. 

Schedules are usually used when encoding availability or activation information, such as in the SAA.ACT, RTE.CLS, AD.CLS, etc. scenarios. In this situation, it is recommended that the input interface provides a "calendar/level" view of the activation/availability, enabling the operator to graphically visualise the status of the feature different times and levels (if applicable), such as in the example below:

In the calendar view, the BASELINE information that remains valid during the Event validity time shall be visibly identified from the information that is specific to the Event, for example by using a different color and fill pattern.

The TEMPDELTA shall contain the complete definition of the activity times, including any eventual time ranges that are recuperated from the BASELINE schedules. Note that according to the OPADD, notification of a schedule modification by NOTAM shall be done by including the new schedule in item E, not in item D. Therefore, the list of Event Scenarios has to include separate scenarios for such situations.

Common coding patterns

The Common coding patterns apply also for Digital NOTAM Event schedules, but with the limitations specified above. This means that only two three types of schedules can be used in Digital NOTAM Events - "Daily/", "date based" or "Weekday based"

"Daily

" based schedules

This applies to schedules that occur every day or on specific dates during the validity period of the data, without distinction between weekdays. However, it is possible to exclude specific dates from the applicable times of the schedule. For example:

• "daily from 09:00 to 12:00 and from17:00 to 1721:00"
• "daily from SR until 18:00 "
• "daily from 07:00 to 23:00 except for 25 Dec and 1st Jan"

The data input elements that are specified for such schedules are indicated in the diagram below:

Image Added

Input_Daily = "[TSH]" ("'daily'") ("start time" | ("start event" ["rel. start"])) ("end time" | ("end event" ["rel. end"])) {note} "[/TSH]" { "[TSH]" ("'daily'") ("start time" | ("start event" ["rel. start"])) ("end time" | ("end event" ["rel. end"])) {note} "[/TSH]"} \n 
{"[TSH]" "excluded date" {note} "[/TSH]"} {"schedule note"}.

"Date" based schedules

This applies to schedules that occur on specific dates during the validity period of the data, without distinction between weekdays. It is not possible to specify a "date period" (such as "from 09 SEP 07:00 until 16 SEP 16:00). However, it is possible to exclude specific dates from the applicable times of the schedule. For example:

• "from 09 until 16 SEP and on 18 SEP, daily from SR until 18:00" (note that this would require two separate Timesheets, one for 9-16 SEP and one for 18 SEP, as it is not possible to specify multiple startDate/endDate on a single Timesheet).

The data input elements that are specified for such schedules are indicated in the diagram below:

Image Added

Input_Date = "[TSH]" (("start date" "end date") | "on date") ("start time" | ("start event" ["rel. start"])) ("end time" | ("end event" ["rel. end"])) {note} "[/TSH]" { "[TSH]" (("start date" "end date") | "on date") ("start time" | ("start event" ["rel. start"])) ("end time" | ("end event" ["rel. end"])) {note} "[/TSH]"} \n
{"[TSH]" "excluded date" {note} "[/TSH]"} {"schedule note"}.

"Days of the week" based schedules

This applies to schedules that occur with a weekly pattern, during the validity period of the data. It is possible to specify both individual weekdays (MON, TUE, etc.) and weekday periods (from FRI 17:00 to MON 07:00). It is possible to exclude specific dates (but not  holidays or other special dates!) from the applicable times of the schedule. For example:

• "MON, TUE, WED, THU, FRI from 13:00 to sunset; SAT, SUN. from 13:00 to 15:00" (this requires five distinct Timesheet, but which have identical values for all fields, except for the day property);
• "SUN, 2300 (2200) to MON, 0500 (0400)"
• "MON to FRI, 09:00 to 17:00, excluding 09 SEP" ("MON to FRI" is coded as five distinct Timesheet, but which have identical values for all fields, except for the day property)

The data input elements that are specified for such schedules are indicated in the following diagram below:Image Removed:

Image Added

where:

Image Added

Image Added

Input_Daily_DateWeekdays = ("weekday" | "week_period") {"weekday" | "week_period"}.

weekday = "[TSH]" "on weekday" ("start time" | ("start date"  event" ["rel. start"])) ("end datetime") | "on date" | "daily")("end event" ["rel. end"])) {note} "[/TSH]" { "[TSH]" "on weekday" ("start time" | ("start event" ["rel. start"])) ("end time" | ("end event" ["rel. end"])) {note} "[/TSH]"} \n
{"[TSH]" "excluded date" {note} "[/TSH]"} {"schedule note"}. 

week_period = "[TSH]" "from weekday" ("start time" | ("start dateevent" ["endrel. datestart"])) |"to weekday" ("onend datetime" | "daily") ("end event" ["rel. end"])) {note} "[/TSH]" { "[TSH]" "from weekday" ("start time" | ("start event" ["rel. start"])) "to weekday" ("end time" | ("end event" ["rel. end"])) {note} "[/TSH]"} \n

{"[TSH]" "excluded date" {note} "[/TSH]"} {"schedule note"}.  

Data input elements

The following table provides provides the mapping of each information item within the AIXM 5.1.1 structure. The name of the variable (first column) is recommended for use as label of the data field in human-machine interfaces (HMI).

"Days of the week" based schedules

Data verification rules

The data verification rules provided in this section shall be followed in order to ensure the harmonisation of the digital encodings provided by different sources. These rules shall be used as complementing the General coding rules for Schedules defined in AIXM Coding Overview - Common Coding Rules - Common coding patterns. In case of contradiction, the rules described below are superseding the general ones.